Back to Blog
    Materials Comparison· 7 min read·10 November 2026

    Tungsten vs Molybdenum: Density, Melting Point and High-Temperature Performance Compared

    Tungsten and molybdenum are the two refractory metals engineers reach for most often when a part has to survive extreme heat. They sit next to each other in the periodic table, share a crystal structure, and are often processed by the same powder-metallurgy route — yet they are not interchangeable. This comparison sets out where the two metals actually differ and how those differences decide which one belongs in a given application. (Jayanth Tungsten manufactures tungsten powders and tungsten chemicals; we do not supply molybdenum, so this is written as a neutral comparison.)

    The headline numbers

    Density: tungsten is about 19.3 g/cm³; molybdenum about 10.2 g/cm³. Tungsten is nearly twice as dense — close to gold — and this single number drives many material choices.

    Melting point: tungsten melts at about 3,422 °C, the highest of any metal; molybdenum at about 2,623 °C. Both are far above steels and nickel superalloys.

    Stiffness: tungsten's elastic modulus is around 410 GPa against roughly 330 GPa for molybdenum, so tungsten parts deflect less under the same load.

    Thermal expansion: both are low, roughly 4.5 × 10⁻⁶/K for tungsten and around 5 × 10⁻⁶/K for molybdenum, close to silicon and many ceramics — which is why both appear in semiconductor and electronic packaging.

    Thermal conductivity: at room temperature tungsten conducts heat somewhat better (around 170 W/m·K) than molybdenum (around 140 W/m·K).

    These are typical values for pure, dense metal; real parts vary with purity, processing and temperature.

    Strength at temperature

    Both metals keep useful strength at temperatures where most engineering alloys have long since softened, but tungsten holds on to it to a higher temperature. Above roughly 1,500 °C molybdenum's strength falls away faster, and in the highest-temperature applications — tungsten filaments, the hottest zones of vacuum furnaces, some rocket nozzle and plasma-facing components — tungsten is the only practical metal.

    Recrystallisation matters as much as melting point. Worked refractory metals gain strength from their deformed grain structure; once heated above their recrystallisation temperature they lose that strength and, especially for tungsten, become more brittle. Molybdenum recrystallises at a lower temperature than tungsten, which is one reason doped and alloyed grades (such as TZM for molybdenum, or potassium-doped tungsten) exist.

    Oxidation: the shared weakness

    Neither metal tolerates hot air. Both form oxides at moderately elevated temperatures, and both oxides become volatile at higher temperatures, so the metal is consumed rather than protected. Molybdenum is worse in this respect: its trioxide begins to evaporate at lower temperatures than tungsten's.

    The practical consequence is the same for both. Above a few hundred degrees Celsius they are used in vacuum, hydrogen or inert gas, or they are coated. If a part has to run hot in air, neither bare tungsten nor bare molybdenum is the answer.

    Ductility and fabrication

    Here molybdenum has a clear advantage. Its ductile-to-brittle transition temperature is lower — typically around or below room temperature for wrought material — so it can be bent, deep-drawn, spun and machined more readily. Tungsten's transition sits above room temperature, which makes it brittle in the workshop: forming usually has to be done hot, and machining calls for carbide tooling and care.

    This is why molybdenum sheet is the default for many furnace heat shields and boats, and why tungsten more often appears as pressed-and-sintered components, wire, or as a constituent of composites such as tungsten heavy alloy (W-Ni-Fe, W-Ni-Cu) and copper-tungsten, where a ductile phase makes the material machinable.

    Cost per kilogram vs cost per part

    Comparing price per kilogram can mislead. Molybdenum is roughly half the density of tungsten, so a kilogram of molybdenum makes almost twice the volume of parts. For a heat shield or crucible, which is sized by geometry rather than weight, molybdenum often comes out cheaper per part even when per-kilogram prices are similar.

    The reverse applies when density is the point. Radiation shielding, counterweights, balance weights and vibration dampers are sized by mass in a limited space, and tungsten's density lets them be smaller — which is often the whole reason for specifying it.

    How engineers usually choose

    Choose tungsten when you need maximum density in a compact space (shielding, counterweights, kinetic-energy components); the highest service temperatures; maximum stiffness; arc-erosion resistance in electrical contacts (as copper-tungsten or silver-tungsten); or extreme wear resistance via tungsten carbide.

    Choose molybdenum when the part is sized by volume rather than mass; when it must be formed, bent or deep-drawn; for most furnace hot-zone components below the very highest temperatures; for glass-melting electrodes; and in lightweight heat-spreader composites such as copper-molybdenum.

    Where both would work, the decision usually comes down to fabrication route and cost per finished part rather than any single property.

    Need tungsten powder for your application?

    ISO 9001:2015 certified · Certificate of analysis with every shipment · WhatsApp replies within a few hours

    WhatsApp Enquiry

    Frequently asked questions

    Is tungsten heavier than molybdenum?

    Yes. Tungsten's density is about 19.3 g/cm³ against about 10.2 g/cm³ for molybdenum, so tungsten is nearly twice as dense. A part of the same size made in tungsten weighs almost twice as much.

    Which has the higher melting point, tungsten or molybdenum?

    Tungsten, at about 3,422 °C — the highest melting point of any metal. Molybdenum melts at about 2,623 °C. Both are classed as refractory metals.

    Can tungsten or molybdenum be used at high temperature in air?

    Not unprotected. Both oxidise at moderately elevated temperatures and their oxides volatilise at higher temperatures, molybdenum's more readily. High-temperature service is normally in vacuum, hydrogen or inert gas, or with a protective coating.

    Why is molybdenum easier to machine than tungsten?

    Molybdenum's ductile-to-brittle transition temperature is lower, around or below room temperature for wrought material, so it deforms rather than cracking. Tungsten is brittle at room temperature, so it is usually formed hot, machined with carbide tools, or used in composites like tungsten heavy alloy that contain a ductile binder phase.

    Ready to place an order?

    Share your grade, F.S.S.S., quantity, and destination via WhatsApp. Our team responds with pricing and availability on business days.